top of page
Search

BER Ratings Explained: The Scale, What’s Good and How to Improve Yours

Writer: Sean Gleeson
Sean Gleeson
5 days ago
4 min read

Every Irish property listing carries a BER label, yet few homeowners could say what separates a C from a D. The picture became more confusing on 24 May 2026, when the scale itself changed and familiar bands such as B2 and C3 disappeared from new certificates.

This guide explains what a BER measures, how the new scale compares with the old one, what counts as good, and which improvements move a rating most.


What is a BER rating?


A Building Energy Rating, carried out by an SEAI-registered assessor, estimates the primary energy a home needs for heating, hot water, ventilation and lighting under standard occupancy, expressed in kWh per square metre per year.


Because occupancy is standardised, it rates the building rather than the habits of the people living in it. A valid BER is required to sell or rent a home, must appear in the advertisement, and is generally valid for ten years.


How has the BER scale changed in 2026?

Under regulations implementing the EU Energy Performance of Buildings Directive, the scale moved from fifteen bands to eight on 24 May 2026. According to SEAI’s guidance on the new scale, the categories are now A0, A, B, C, D, E, F and G, with A0 reserved for the most efficient buildings that use no fossil fuels.


Certificates issued before that date remain valid for ten years from issue, so no reassessment is needed simply because the scale changed. New certificates also show greenhouse gas emissions, the contribution of renewable energy and recommendations for improvement.


What does the BER scale look like now?


The new thresholds below are as summarised in BER Essential’s homeowner guide, with the old bands taken from SEAI’s homeowner leaflet.

New band

Energy value (kWh/m²/yr)

Old bands it broadly replaces

Typical homes

A0

42 or less, plus zero-emission criteria

None (new tier)

New, fully electric homes

A

75 or less

A1, A2, A3

New builds and deep retrofits

B

Over 75, up to 150

B1, B2, B3

Well-insulated homes, efficient heating

C

Over 150, up to 225

C1, C2, C3

Typical 1990s and 2000s homes

D

Over 225, up to 275

D1 and part of D2

Older homes, partial upgrades

E

Over 275, up to 325

Parts of D2 and E1

Poorly insulated older homes

F

Over 325, up to 375

Parts of E1 and E2

Older homes, little insulation

G

Over 375

Part of E2, F, G

Least efficient homes

Lower-band boundaries do not align exactly, so the mapping is approximate.

The upper bands simply merge the old sub-bands, so an old B2 sits within the new B. Towards the bottom, however, the thresholds tightened: G previously began above 450 kWh/m²/yr and now begins above 375. Owners of older homes with a historic F or E rating may therefore wish to check where their energy value falls before commissioning a new assessment for a sale or letting.

G now starts above 375 kWh/m²/yr rather than 450, so a home rated F under the old scale could score a G today without any change to the building.


What is a good BER rating?


New builds are expected to achieve an A, and analysis of CSO data reports that around 3,000 dwellings received the new A0 rating in the first five weeks of the scale, all of them heated by electricity.


For an existing home, a B is a strong result and broadly the standard SEAI targets in whole-home upgrades, while a C is typical of 1990s and 2000s housing. Ratings of D and below usually mean higher heating bills, cold rooms and condensation.



How do I find my BER rating?


Existing certificates can be retrieved through the SEAI BER register. Homes without a valid certificate need an assessment from an SEAI-registered assessor, typically priced in the low hundreds of euro.


How can I improve my BER rating?


The biggest gains usually come from reducing heat loss through the fabric and improving the heating system, although the effect of each measure depends on the starting point. A pre-works BER is a sensible first step, since the assessor’s advisory report shows where a home loses the most energy.

Improvement

Typical effect on rating

Relative cost

Trade

Attic insulation

Moderate to high where none exists

Low

Insulation contractor

Cavity or external wall insulation

High

Medium to high

Insulation contractor

Heat pump replacing oil or gas

High

High

Heating installer, electrician

Heating controls and zoning

Moderate

Low to medium

Plumber, electrician

Cylinder insulation and immersion timer

Low to moderate

Low

Plumber, electrician

Window and door upgrades

Moderate

Medium to high

Window installer

Solar PV panels

Moderate

Medium

Solar installer, electrician

LED lighting

Low

Low

Electrician

Draught-proofing and ventilation

Low to moderate

Low

General maintenance, electrician

Modern heating controls, a timed immersion and LED lighting are inexpensive and contribute directly to the calculation. Fabric upgrades should follow the condition of the roof, since insulating an attic beneath a leaking roof wastes the investment.


SEAI offers grants for insulation, heat pumps and solar panels, but terms change periodically and should be checked with SEAI before work is planned.


Need plumbing, electrical or roofing support in Dublin?


With older certificates still valid and every new assessment using the A0 to G scale, it pays to know where a home stands before it is reassessed, and for most existing homes improvement starts with the fabric and the heating system.


Abbington’s plumbers, electricians and roofers carry out many of these upgrades across Dublin, from heating controls, immersion timers and extractor fans to roof repairs ahead of insulation. Get in touch to discuss the work your home needs.


Planning upgrades to improve your BER? Call Abbington on 087 465 8338 to discuss heating, electrical and roofing work.

 
 
 

Comments


bottom of page